VINTAGETRACTORS.COM
AND
RUSTY ACRES RANCH
Parts for John
Deere Model A - Engine Parts
A577R Flywheel nut and Spade lug socket wrench, $80,
fits A, D, and G tractors, $80
Used compression release valve, $20, two for $35
COMING SOON
A3367R Head, Checked by my local machine shop and valves
and valve seats were ground, two new intake valves, Ready to go
to work, $400
A2093R Drain plug for head, $20
- 
- 
A3366R Block, standard bore. This block has been magnafluxed
by my local machinist and there are no cracks , breaks, or repairs.The
bores are smooth and should need just a light honing, The pair
of standard A3282R pistons that came from the block is included.
$495
- 
- 
-- 
A3703R Block, standard bore. This block had antifreeze
in the system when parted and there are no cracks , breaks, or
repairs.The bores are smooth and should need just a light honing,
The pair of standard A3282R pistons that came from the block is
included. $435
A2344R connecting rods with shims, very good condition,
$70 each
A2338R set #2 standard bore pistons, $30 each or $60/pair
- 
- 
A3530R piston, 5 1/2" standard bore gasoline pistons,
with piston pin (#1 does not have a pin), $30 each
- 
-
A3282R standard bore piston, six available, three shown,
$30 each
B1608R starter ratchet, excellent condition, no breaks
or repairs, $70
- 
-
A3264R flywheel #1, very good condition, good splines,
good ring gear, $125
A3264R flywheel #4, very good condition, good splines,
good ring gear, $125
A3264R flywheel #5, very good condition, good splines,
good ring gear, $125
A2360R crankshaft #3 very good splines flywheel end,
splines need attention on clutch end, good bearing surfaces, $40
- 
A3322R Crankshaft #1 for A over 584000, with very good
bearing sufaces and very good splines on crankshaft end, splines
on driving disk end show some wear, as-is, $45
- 
A3322R Crankshaft #2 for A over 584000, with very good
bearing sufaces and very good splines on crankshaft end, splines
on driving disk end will need to be built up and machined, as-is,
$25
A3312R flywheel nut, used and usable, $18
A159R spacer on clutch end of crankshaft, $5
For A >584000, A3266R Oil slinger cover, $10, A85R
Oil slinger $10
-
Bearing housing with good bearings and shims, both
A2884R and A3265R or A2885R available, $40 each, If you need only
the bearings, I can remove them from the housings to save weight
and shipping cost.
A302R Shim packs for main bearings
A2326R 5/8 x 7 3/16" stud for block to head, $7
each
Head Nut, $1 each or 9 for $6
- 
Aftermarket Gas manifold for A under 584000, to replace
A2383R, very good condition, $25
- 
A3386R manifold #4 for A over 584000, good condition,
$65
- 
A3386R manifold #3 for A over 584000, good condition,
$65
- 
A3386R manifold #2 for A over 584000, good condition,
but need to have three studs removed and gasket surface resurfaced,
$35
- 
A3386R manifold #1 for A over 584000, good condition,
$65
-
A3386R manifold #3 for A over 584000, good condition,
$65
-
AA4014R (AA3954R) Exhaust pipe for A over 584000, good
used, $20 easch, your choice
AA2214R Muffler, used but still has life left in it,
as-is, $20
A1386R muffler casting for AR/AO, as-is, $15
Retainer clips for valves, $8/pair
Valve spring: $2
Cap, $2
Intake and exhaust valves, $10 each
Tappet assembly $80
A2346R Tappet lever, $9
F2559R Adjusting screw, $19
A2349R Shaft, $5
A2350R Bracket, $10
D376R Spring, $4
24H248R Washer. $1
A602R Snap ring. $2
Tappet oiler, $25
Special stud for tappet assembly
and valve cover, $7
A2363R stud for tappet assembly
and valve cover, $10
Set of two A2363R stud for tappet
lever assembly with nuts and acorn nuts,.$25
A2354R Oil Outlet washer, $12.50
A4227R Oil Outlet washer, $12.50
A30R cam gear, all teeth is very good condition, no
chips or repairs, one only, $60
A3583R (asbove s.n. 630323) or A1142R camshaft (s.n.
477000-620323), $40
A355R spring at the send of the camshaft, $10
A3582R camshaft left side bearing cap, $5
Cam followers, $5 each, $16 for set of 4
A1595R Cam Follower guide with oil pump drive gear,
$20
A1290R Push rods, $5 each, set of 4 for $18
14H665R Original acorn nut for valve cover, $3 each
A2347R or AA4016R Valve cover,
$10
A3296T oil line $8
AA4936R elbow, $8
A3296R oil pipe. $8
A2501R elbow, $8
A2502Rstraight fitting, $5
- 
Oil line to oil gauge, $8, your choice
AA280R Oil pipe to LH main bearing, $15
AA281R OIl Pipe to LH Main bearing, $20
AA819R Oil pipe to governor, $25
AA802R Oil pipe Pump discharge, $15
AA6476R, oil line to oil pressure gauge, $20
AA3988R (up to #694827), oil line to RH main bearing,
$20
AA3989Roil line to LH main bearing, $20
AA3991R Oil line to governor, $20
AA6476R Oil line to oil indicator, $20
AA3993R Oil Line to tappet levers, $20
AA3990R Oil line , oil pump discharge, $15
D2440R Connector, $6
E1994R Connector, $5
A258R connector, $6
A1252R Governor connector, $5
Oil filter head with A1277R casting number on top piece,
for A under 584,000, $60
- 
Oil pump, $35, tested and pumps oil
R20248R (A1152R) Oil filter housing,
$25
AA2096R Oil filter outlet, $15
A522R Oil filter cover with nut, spring, and plate
(missing snap ring), $40
A522R Oil filter cover, $6
A524R Oil filter bottom nut,
$6
D793R and D794R Oil level test
cock, $10
- 
Water pump with A4280R housing and A4298R impeller,
no leaks, came from a tractor filled with antifreeze in the cooling
system, turns freely as it should, $100
- 
AA1342R Heat Indicator Gauge, $30
Shorter choke rod for A over 584000, $20
A3394R Crankcase cover, A over 584,000, $10
A2232R crancase cover, no breaks or repairs, excellent
condition, $40
A2233R Breather, used with A2246R cover, $25
A2234R cover for A2233R breather, $12.50
Core for above breather, $12.50
A2233R brather housing, $20
A2234R cover, $10
D1952R Breather filter, $12
AC762R shorter Breather cap, $15
AA359R crankcase breather cap, $18
Breather cap clamp $5 each and springs, $2 each
C1438R spring on throttle lever shaft, new, $7 or good
used, $4
A80R throttle lever, $20
A1184R throttle rod, $14 - Please give me the overall
length of your rod, so I can be sure to send the right one!
14 1/4" Throttle rod, $12 - Please give me the
overall length of your rod, so I can be sure to send the right
one!
A4120R Short throttle rod, $12
A3355R throttle rod for A > 584000, $14 - Please
give me the overall length of your rod, so I can be sure to send
the right one!
13 inch throttle rod, $12
26 inch throttle rod, $14
A3298R 41 inch Choke rod A 584000-662728, $25, your
choice
B2122R keeper $10
D1720R retainer lock, $5 each half
AA3717R fan, with two cups, $25
- 
A1177R fan gear, some pitting but very usable, $50
B2123R fan disk, $20, several available
D399R Friction washer, $4
A4059R Fan Drive Cup, $9
B2124R pulley, good splines,
$25
B2874R pulley, good splines,
$30
A3066R spring, $8
B298R felt retainer and washer, $10
A846R spring, $6
B2121R reatiner, $7
D1736R washer, $3
A3066R spring, $5
Fan bearing set for front of fan JD7656R,JD7657R, and
JD7655R, $20
- 
Ventilator pump with B2644R Body, B2640R Housing, and
B2830R cover, $35
- 
Ventilator pump with A4189R Housing, and A4188R cover,
$35
A3055R Housing, $15
AF637R Fanshaft housing, $25, your choice
- 
A3668R Fan shaft, $35, your choice
JD7657R bearing for governor and fanshaft, $15
- 
A844R Fan support, $9
A2112R center plate. $15
A2166R Ventilator tube, $25
AA4035R Ventilator Inlet Pipe, $20
AA4033R Ventilator Outlet pipe, $20
A41R end cap for governor, $10
A3285R end cap for governor, $10
A1241R arm with other governor parts, $15
Governor arm and shaft, $15
A3408R Speed control lever, A>584000, $10
AC667R governor weights, very good condition, pins
are nice and tight on the arms, $35
- 
Internal governor parts for A over 584000 #1, A3339R
and A3268R gears are good, $90
- 
Internal governor parts for A over 584000 #2, A3339R
and A3268R gears are good, $90
- 
Internal governor parts for A over 584000 #3, A3339R
is fair and A3268R gear is good, $60
Internal governor parts for A over 584000, A3339R and
A3268R gears are good, both weights are missing,
A3339R bevel gear with governor shaft, gear in good
condition, $25
A3286R governor arm and shaft, $15
A2495R Shoulder bolt, $2 each
A2422R Governor case, $20
- 
A3267R Late A governor case, $20, your choice
Governor end cap with JD7657R bearing, $30